【iSolver案例分享31】轴承受力分析
【iSolver案例分享31】轴承受力分析
1. 案例背景
本案例为某型轴承零件的静力学分析,模型为回转体类轴对称三维实体结构,考虑到模型几何形状较为简单,采用全尺寸模型建模。该轴承模型选用的单位制为mm-MPa-s制,结构材料为钢,其弹性模量为200000MPa,泊松比为0.32。
图1 几何模型
2. 有限元处理
约束条件为轴承底面固支,载荷条件为内侧壁面施加20MPa的压强推力载荷。
图2约束及载荷条件
由于结构形式较为规整,为保证模型的求解精度和求解效率,整体采用六面体网格划分,单元类型选用实体单元C3D8R,模型共划分为2532个单元。
有限元模型建立完成检查无误之后,分别利用ABAQUS和iSolver求解器进行求解,结果对比见第三部分。
图3 有限元网格
3. 结果对比
3.1 Mises应力结果对比
a) iSolver 求解Mises应力视图1
b) iSolver 求解Mises应力视图2
c) ABAQUS 求解Mises应力视图1
d) ABAQUS 求解Mises应力视图2
3.2 应变结果对比
a) iSolver 求解应变视图1
b) iSolver 求解应变视图2
c) ABAQUS 求解应变视图1
d) ABAQUS 求解应变视图2
3.2 位移结果对比
a) iSolver 求解位移视图1
b) iSolver 求解位移视图2
c) ABAQUS 求解位移视图1
d) ABAQUS 求解位移视图2
4. 结果对比总表
由以上结果云图分析可知,iSolver和ABAQUS两个求解器对同一模型分析的结果同一性较好,应力应变的最值发生位置一致,具体数值分析见下表。
iSolver |
ABAQUS |
|
应力 |
1.991E1 |
1.99E1 |
应变 |
4.164E-5 |
4.16E-5 |
位移 |
1.057E-3 |
1.06E-3 |
5. iSolver免费下载
iSolver为免费软件,且无license限制,最新版免费下载地址如下:
https://www.jishulink.com/content/post/337351
6. 以往iSolver案例
https://www.jishulink.com/content/post/1308235
第2篇:标准紧凑拉伸(CT)试样的弹塑性分析
https://www.jishulink.com/content/post/1311068
第3篇:理想弹塑性简支梁三点弯曲
https://www.jishulink.com/content/post/1312567
https://www.jishulink.com/content/post/1314142
https://www.jishulink.com/content/post/1787486
https://www.jishulink.com/content/post/1788519
https://www.jishulink.com/content/post/1789593
https://www.jishulink.com/content/post/1793131
https://www.jishulink.com/content/post/1791578
https://www.jishulink.com/content/post/1796589
https://www.jishulink.com/content/post/1802796
https://www.jishulink.com/content/post/1805030
https://www.jishulink.com/content/post/1808197
https://www.jishulink.com/content/post/1813708
https://www.jishulink.com/content/post/1819421
https://www.jishulink.com/content/post/1821735
https://www.jishulink.com/content/post/1824652
https://www.jishulink.com/content/post/1830523
https://www.jishulink.com/content/post/1836426
https://www.jishulink.com/content/post/1842480
第21篇:自主化圆柱建模及静力分析
https://www.jishulink.com/content/post/1845836
https://www.jishulink.com/content/post/1846655
第23篇:镂空钢板的承压测验
https://www.jishulink.com/content/post/1850649
第24篇:球面网壳模态分析
https://www.jishulink.com/content/post/1849299
第25篇:假肢脚踝受冲击荷载
https://www.jishulink.com/content/post/1852457
第26篇:欧拉梁单元弯矩计算
https://www.jishulink.com/content/post/1856479
第27篇:桩靴的承压测验
https://www.jishulink.com/content/post /1859305
第28篇:吸力桶的力学性能测试
https://www.jishulink.com/content/post/1862342
第29篇:弹塑性钢架桥梁的模态分析案例
https://www.jishulink.com/content/post/1864145
第30篇:压力容器受内压仿真案例